Keeping Conveyor Belts on Track

Top Quality Ride On Lawnmower -
 Volvo auger sensor – LEEHUI

When you are in a place where you want to think about moving goods from one place to another in your facility, you’ll discover that getting a conveyor system is one of the best options open to you. They are reliable, they are straightforward, and once you get them installed, you’ll find that they can run quite smoothly with a minimum amount of basic maintenance. But, you will need to remember – if you want to make sure that your conveyor belts continue operating for years – that you are going to need to pay some special attention to your conveyor belts tracking or alignment at the time of installation.

Basics to achieve an effective Conveyor Belt Alignment

Let’s talk about alignment and what it takes for conveyor belts to be properly aligned. To be properly aligned, conveyor belts consistently need to have their edges within the width of the pulley face and within the confines of any other rolling elements, like the return rolls and the idlers. This should be tested while the belt is under a full load condition. To complete this task, the components need to be set at ninety degree angles to a common centerline and perfectly level across the width of the belt.

There are some things that will affect the alignment and acuity of your conveyor systems. Though this sounds like an extensive list for your conveyor systems, you’ll discover that it is fairly easy to achieve. These things include:

1. The amount of power and tension that is run through the belts by drives, rolling elements and take-up systems.

2. The centering of the load at the point of dumping the material onto the conveyor belts.

3. The accuracy of the alignment of each rolling component to the belts.

4. The construction of, deformities in the belts as well as its type and how long it is has been in operation.

5. Accumulation of dirt and water on the backside of the belt.

‘Power and Tension’ Factor

Consider the place of power and tension and as to how they affect the efficiency of your conveyor belts. For instance, if you have a belt that is under too much tension, you’ll discover that this will put extensive unnecessary wear on your rolling elements. This can result in premature failure of splices, the belts edges curling up or cupping and in a surprisingly short amount of time, you’ll find that you need to realign your belt yet again. When you have a belt that is too loose, it will be significantly more prone to slippage and sagging between the idlers. Not only does this make for less than optimal performance, you’ll find that there are going to be some severe issues when you got to start it up and also, reduces your ability to get the most work out of the horsepower that is going in.

‘Backside of the Belt’ Factor

When you think about your conveyor system, you might first think of the rolling elements and the top of the conveyor belt, but also be aware that the backside of the belt is important too. This part will provide the friction that transfers the drives’ torque to the belts and essentially, it is the part that creates the rolling action of the idlers and the tail pulley. The backside of the belt is hard to see, and the problem is that too many people simply think ‘out of sight, out of mind’. The truth is that unless you pay attention to the backside of the belts and the condition that it is in, you are certainly going to see the delays and disasters that come with belt slippage. Take some time and make sure that you check the backside for dirt and water by installing the requisite belt cleaning supplies. These are very straightforward and will do the job well.

‘Effective tracking of conveyor belts’ is one of the most important things to consider when you are ready to take on installing your conveyor belts, so don’t rush and take some time to ensure that everything’s done to a tee.


Keeping Conveyor Belts on Track Related Video:


Persisting in "High good quality, Prompt Delivery, Aggressive Price", we've established long-term cooperation with shoppers from each overseas and domestically and get new and previous clients' high comments for Heating Rod For Tamper Ba , Dynapacscreed Plate , Hardox450 Screed Plate , Our factory insists on the principle of "Quality First, Sustainable Development", and takes "Honest Business, Mutual Benefits" as our developable goal. All members sincerely thanks for all old and new customers' support. We will keep working hard and offering you the highest-quality products and service.Thanks.